Blog Archives

Give your furniture an antiqued or distressed look

Distresse look furniture

A few years ago while in high school I learnt about antiquing, now when I look at this table that has been in the storage room for some time and I need to use it again but the is not budget I thought back to that. This technique is very simple and it gives furniture a character and best of all it can be used on just about anything from frames to tables and cupboards

Antique finish

The trick thought is making the worn effect realistic. To know where exactly to apply the worn effect, except for the edges try handles and areas that are handled regularly and to know what the history of your article is. That is has it been painted over and over before or has is just been painted once.

If your history is continuous painting you will need two different paints it preferred that the top coat be brighter than the top to get the full effect of the distressing and for the painted once effect you will need just one paint and the effect will reveal the bare wood below.

 

Layered didtressed look

Layered didtressed look

To preserve the genuineness of your colour choice for long, you will need to paint clear polyurethane over the finished project. A water-based polyurethane that won’t yellow over time and is therefore my best choice.

You will need to clean and sand down your chosen furniture before you start painting on it.

Distressed-Furniture

Paint the whole piece in the base coat colour you’ve selected then for the bare-wood look: When the base coat is dry, start sanding off areas that would naturally end up distressed do not get carried away with the sanding and sand too much of the paint off then wipe the furniture piece with a cloth.

Layerd detail

Paint the whole piece in the base coat colour you’ve selected, for the two colour look: Rub candle wax on the areas where you’d like to see colour show through. Don’t forget to do the sides and back; you want the entire piece to be finished. Then apply the top coat over the base coat and the wax, cover the entire furniture piece well. After the paint dries, rub the steel wool over the areas you’ve waxed, if you dip it in hot water it will be quicker and easier then wipe off the piece with the cloth.

 

Apply a finish if desired

Advertisements

DIY Epoxy Garage Floor coating.

 

Epoxy covered garage Floor

 

There are a number of nationally and international professional floor coating companies but installing your own epoxy floor coating can be cost-effective and gratifying. A garage, play room or lapa area might not be the show off room of your house, installing attractive floor coating can help make it more appealing. This is similar to the staining the concrete that was done in my previous post but for more heavy duty use. It comes in various colours so you can choose according to the rooms specific décor and colour scheme.

The various colours of Epoxy paint

 

 

 

 

 

 

 

 

 

 

 

 

Before you start, remove all furniture and items in the garage, clean the floor as best as possible and ensure the floor is level and roughly smooth by sanding if possible. Remove dust from cracks and corners to ensure that the Epoxy adheres to the floor as firm as possible, remove oil stains to the best of your ability then use either air-pressure or water-pressure spray the day before the application to ensure the floor is well dried, it is important to ensure that no moisture is still on the floor as this would not adhere otherwise.  If the floor was previously sealed or painted remove with the relevant remover well in advance. To test for this presence, pour a small amount of water onto the floor if it seeps in there is no sealant and if it doesn’t, and instead forms beads of water on top, the floor still has some sealant.

Vinyl Chip Epoxy Floor colour

Each of these preparation steps may be performed multiple times to ensure the whole surface is well prepared for priming. The process may take several days.

Mask of any areas that need to be protected with wide masking tape.

Please wear protective gear, it is essential to wear protective gloves, rubber boots, and safety glasses

Primer Application

Epoxy Floor Paint

Once the entire floor surface has been prepapred for coating, it is time to apply the primer. The primer is applied just like paint and allowed to settle for several hours before the epoxy goes on. This process is very simple and requires general painting tools, like a roller and a splash pan. Directions on the epoxy bottle should be followed, these may vary slightly between the different manufacturers but the generally go this way.

Apply the supplied EPOXYShield concrete etch and then rinse thoroughly and allow to dry completely, please note it will be easier to work in sections as opposed to  applying to the entire floor.Allow the floor to dry completely before moving on to the next step, this may take several hours.

 

Paint chips In the Paint

Depending on the manufacturer and the kind you have chosen, stir the contents of cans A and B and then pour A into B and mix well for approximately 3 to 5 minutes, then use a wide paintbrush to apply around the perimeter for a neat finish.

Pour epoxy into the paint tray. Insert the extension handle into the roller, dip in the paint tray and apply an event coating onto the surface working in small sections guarantees that the decorative paint chips will be scattered into the freshly coated surface.

Polishing off, the final touch

Do not use the area for at least 16 hour and make sure it is well ventilated

%d bloggers like this: